Luma Pure Red 100W 90 LED Grow Light Panel

INTRODUCING THE LATEST DESIGN IN LED HYDROPONIC TECHNOLOGY !

LED PLANT GROWING LIGHT
( ILGL804-100W）

Wavelength: Red: 660+5nm

1. Product Introduction
LUMA LED GROW LIGHT utilizes the cutting-edge LED plant growing technology, and it consists of many high intensity, fixed wavelength LED bulbs. The RED bulbs can satisfy all the light needs during the plant growth process.

LUMA LED light is very efficient to transfer electricity into light energy. The light spectrum it produced fits the best to what needed for photosynthesis, thus it is extremely lightenergy efficiency (almost 100%, 10 times than conventional light), and maximally reduces energy dissipation. The LED operates coolly, and only emits few heats (does not emit unwanted infrared, will not be detected by any infrared detecting devices), so it will not burn the plants. A 100W LED grow light is equivalent to a 400W High Pressure Sodium (HPS) Light (please refer to the SPD chart) to the plant. The LED bulbs are high intensity and long life (above 50000 hours).

LUMA LED LIGHT can be used as a complement plant grow lighting source or to extend the lighting time for both indoor and outdoor plants.

2. Specifications
Operation Voltage: AC120/+10% 60Hz
Input Current : 500 mA
Power Consumption : 100W
Operation Environment: -28℃～30℃ RH≤90℃
1W High intensity LED bulbs: 90 x Red
Wavelength: Red: 660+5nm, Blue: 465+5nm
Intensity: ≥5000LU*30CM
Maximum Working area: ≥80㎡
Operation height: 0.3/0.6/0.9 m
Over-heat protection: Yes
Dimension : 300x300x135mm
Working angle : 120°

3. Product Layout

4. Important Notices
Please read these instructions carefully before installing the product and keep the manual for further reference.
1) Check the compatibility of the product with the local power supply before installation.
2) Check the power circuit regularly. DO NOT use the product if the plug, power wire or the product itself is broken.
3) For further protection, install a current leakage protector (RCD) with rating current no more than 30 mA.
4) DO NOT let children approach this product.
5) Store in dry place when not in use.
6) Clean the transparency cover regular otherwise the intensity may be reduced.
7) DO NOT separate the product without engineer authority.
8) DO NOT spill water on the product, this may damage the product.
9) Power must be CUT OFF before changing the A/B mode.

5. Installation and Use
1) Please hang the product 0.3-0.9m above the plants as the following graph.

2) Plug one side of the power wire into the wire inlet of the light and the other side into the power socket.
3) Put the switch on “ON” position to turn the light on.
4) After the light switched on, the fan on top of the light will keep on operating - stop - operating for ventilation.
5) The growth of plant has special requirements on light and temperature. Our company has developed a light-temperature-time controller to free the operator from complicate work. Please ask the retailer for more information.

6. Troubleshooting
Please contact us if either of these problems cannot be resolved.

7. Warranty and Service
1. All products have been carefully tested in factory. Any quality problem will be covered by one year warranty or get changed for free. (Depending on the situation and decision will be made by our company ONLY)
2. Any damage caused by authorized separation of product will NOT be covered by warranty.
3. To help customer have better use of the plant grow LED light, our company can offer more technical support about plant growing. If have any problem, please feel free to contact us and we promise to offer you the best service.

Customer Reviews:

You may also be interested in this/these product(s)

Luma Pure Blue 100W 90 LED Grow Light Panel Regular Price: $375.00 Sale Price: $285.00 You Save: $90.00